Шпаргалки

Инструменты пользователя

Инструменты сайта

Вы посетили: • nt98562
nt98562

Это старая версия документа! 

<pre>
NPIp>Tdma1 ini_ver 0x00000001
ETH trim = 000012FC
speed 0000029A
winbond
Non S3
>ddr2
dma ok
 
UNZOK!
Loader Start ...
LD_VER 03.00.00
 
562_DRAM1_666_512Mb 08/24/2021 01:48:41
 
No card inserted
Pad driving increased
SPI NOR MID=00000020,TYPE=00000070,SIZE=00000017=>00800000
SPI NOR
Dual_read
tmp_addr 0x02000000
LdCtrl2 0x00000000
Dual_read
uboot_addr 0x03900000
uboot_size 0x006C0000
Dual_read
compress header 0x0000005D
inbuf 0x02000000
outbuf 0x03900000
in_len 0x00030000
E:.E:.E:.E:.E:.E:.E:.E:.E:.nodep 0x0010365C
NVT_LINUX_SMP_OFFfdt 0x00100000
shm 0x00200000
jump 0x03900000
 
 
U-Boot 2019.04 (Aug 24 2021 - 01:48:51 +0800)
 
CPU:   Novatek NT @ 960 MHz
DRAM:  64 MiB
Relocation to 0x03edf000, Offset is 0x005df000 sp at 03bca120
ARM CA9 global timer had already been initiated
otp_init!
120MHz
otp_timing_reg= 0xff6050
Loading Environment from SPI Flash... @nvt_spinor_probe_slave(): sr1: 0x28, sr2: 0xFF
id =  0x20 0x70 0x17 0x20 0x00
eFlashType: 17.
Flash Name: XM_XM25QH64A{0x207017), 0x800000.
@nvt_spinor_validate_params(), XmSpiNor_ProtMgr_probe(): OK.
STDR64FW with page size 256 Bytes, erase size 64 KiB, total 8 MiB
CONFIG_CLOSE_SPI_8PIN_4IO = y.
lk=>10, 0x780000.
SRx val: {[1, 0x28], [0, 0x0], [0, 0x0], [0, 0x0]}, SrVal: 0x100000000000028.
nvt spinor 1-bit mode @ 48000000 Hz, read_opcode: 0x3B, program_opcode: 0x2.
OK
@nvt_spinor_probe_slave(): sr1: 0x28, sr2: 0xFF
id =  0x20 0x70 0x17 0x20 0x00
eFlashType: 17.
Flash Name: XM_XM25QH64A{0x207017), 0x800000.
@nvt_spinor_validate_params(), XmSpiNor_ProtMgr_probe(): OK.
STDR64FW with page size 256 Bytes, erase size 64 KiB, total 8 MiB
CONFIG_CLOSE_SPI_8PIN_4IO = y.
lk=>10, 0x780000.
SRx val: {[1, 0x28], [0, 0x0], [0, 0x0], [0, 0x0]}, SrVal: 0x100000000000028.
nvt spinor 1-bit mode @ 48000000 Hz, read_opcode: 0x3B, program_opcode: 0x2.
@do_spi_flash_probe() flash->erase_size: 65536, flash->sector_size: 65536
fdt init fail return 6156288
DTS find cpu freq clock 960MHz
Set CPU clk 960MHz
Net:   na51089_eth_initialize 1.0.0.1
phy interface: LED2
phy interface: INTERNAL MII
eth_na51089
Warning: eth_na51089 MAC addresses don't match:
Address in SROM is         00:80:48:ba:d1:30
Address in environment is  00:12:31:bb:24:bf
 
Hit X to stop autoboot:  0
@nvt_spinor_probe_slave(): sr1: 0x28, sr2: 0xFF
id =  0x20 0x70 0x17 0x20 0x00
eFlashType: 17.
Flash Name: XM_XM25QH64A{0x207017), 0x800000.
@nvt_spinor_validate_params(), XmSpiNor_ProtMgr_probe(): OK.
STDR64FW with page size 256 Bytes, erase size 64 KiB, total 8 MiB
CONFIG_CLOSE_SPI_8PIN_4IO = y.
lk=>10, 0x780000.
SRx val: {[1, 0x28], [0, 0x0], [0, 0x0], [0, 0x0]}, SrVal: 0x100000000000028.
nvt spinor 1-bit mode @ 48000000 Hz, read_opcode: 0x3B, program_opcode: 0x2.
@do_spi_flash_probe() flash->erase_size: 65536, flash->sector_size: 65536
device 0 offset 0x40000, size 0x2e0000
SF: 3014656 bytes @ 0x40000 Read: OK
srcAddr: 0x2000000, dstAddr: 0x3500000, apFileName[0]: boot/uImage.
created_inode 0x3bf8f30
find_squashfs_file: name bin, start_block 0, offset 1654, type 1
find_squashfs_file: name boot, start_block 0, offset 1746, type 1
read inode: name boot, sb 0, of 1746, type 1
find_squashfs_file: name uImage, start_block 0, offset 1686, type 2
read inode: name uImage, sb 0, of 1686, type 2
write_file: regular file, blocks 7
len 1629112
### get_squashfs_file OK: loade 1629112 bytes to 0x3500000
   Image Name:   Linux-4.19.91
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1629048 Bytes = 1.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
 Linux Image is at 3500000, uboot fdt image is at 3bcf108, loader tmp fdt address is at 100000
bootm 3500000 - 3bcf108
## Booting kernel from Legacy Image at 03500000 ...
   Image Name:   Linux-4.19.91
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1629048 Bytes = 1.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 03bcf108
   Booting using the fdt blob at 0x3bcf108
   Loading Kernel Image
   Loading Device Tree to 028f9000, end 028ffd9d ... OK
osMemStart: 0x0, osMem: 0x2900000.
@fdt_fixup_memory_banks(), ddrStart: 0x0, ddrAll: 0x4000000, hdalStart: 0x2900000, hdalSize: 0x1700000, size[0]: 0x2900000.
 
 
 
Starting kernel ...
 
ACTLR: 0x00000004
ACTLR: 0x00000044
Disable MMU
Clear MMU
Uboot L2 cache aux val: 0x72420000
Uboot L2 cache prefetch ctrl val: 0x70800000
Uboot L2 cache ctrl val: 0x00000000
Done
Uncompressing Linux... done, booting the kernel.
▒в
NPIp>Tdma1 ini_ver 0x00000001
ETH trim = 000012FC
speed 0000029A
winbond
Non S3
>ddr2
dma ok
 
UNZOK!
Loader Start ...
LD_VER 03.00.00
 
562_DRAM1_666_512Mb 08/24/2021 01:48:41
 
No card inserted
Pad driving increased
SPI NOR MID=00000020,TYPE=00000070,SIZE=00000017=>00800000
SPI NOR
Dual_read
tmp_addr 0x02000000
LdCtrl2 0x00000000
Dual_read
uboot_addr 0x03900000
uboot_size 0x006C0000
Dual_read
compress header 0x0000005D
inbuf 0x02000000
outbuf 0x03900000
in_len 0x00030000
E:.E:.E:.E:.E:.E:.E:.E:.E:.nodep 0x0010365C
NVT_LINUX_SMP_OFFfdt 0x00100000
shm 0x00200000
jump 0x03900000
 
 
U-Boot 2019.04 (Aug 24 2021 - 01:48:51 +0800)
 
CPU:   Novatek NT @ 960 MHz
DRAM:  64 MiB
Relocation to 0x03edf000, Offset is 0x005df000 sp at 03bca120
ARM CA9 global timer had already been initiated
otp_init!
120MHz
otp_timing_reg= 0xff6050
Loading Environment from SPI Flash... @nvt_spinor_probe_slave(): sr1: 0x28, sr2: 0xFF
id =  0x20 0x70 0x17 0x20 0x00
eFlashType: 17.
Flash Name: XM_XM25QH64A{0x207017), 0x800000.
@nvt_spinor_validate_params(), XmSpiNor_ProtMgr_probe(): OK.
STDR64FW with page size 256 Bytes, erase size 64 KiB, total 8 MiB
CONFIG_CLOSE_SPI_8PIN_4IO = y.
lk=>10, 0x780000.
SRx val: {[1, 0x28], [0, 0x0], [0, 0x0], [0, 0x0]}, SrVal: 0x100000000000028.
nvt spinor 1-bit mode @ 48000000 Hz, read_opcode: 0x3B, program_opcode: 0x2.
OK
@nvt_spinor_probe_slave(): sr1: 0x28, sr2: 0xFF
id =  0x20 0x70 0x17 0x20 0x00
eFlashType: 17.
Flash Name: XM_XM25QH64A{0x207017), 0x800000.
@nvt_spinor_validate_params(), XmSpiNor_ProtMgr_probe(): OK.
STDR64FW with page size 256 Bytes, erase size 64 KiB, total 8 MiB
CONFIG_CLOSE_SPI_8PIN_4IO = y.
lk=>10, 0x780000.
SRx val: {[1, 0x28], [0, 0x0], [0, 0x0], [0, 0x0]}, SrVal: 0x100000000000028.
nvt spinor 1-bit mode @ 48000000 Hz, read_opcode: 0x3B, program_opcode: 0x2.
@do_spi_flash_probe() flash->erase_size: 65536, flash->sector_size: 65536
fdt init fail return 6156288
DTS find cpu freq clock 960MHz
Set CPU clk 960MHz
Net:   na51089_eth_initialize 1.0.0.1
phy interface: LED2
phy interface: INTERNAL MII
eth_na51089
Warning: eth_na51089 MAC addresses don't match:
Address in SROM is         00:80:48:ba:d1:30
Address in environment is  00:12:31:bb:24:bf
 
Hit X to stop autoboot:  0
@nvt_spinor_probe_slave(): sr1: 0x28, sr2: 0xFF
id =  0x20 0x70 0x17 0x20 0x00
eFlashType: 17.
Flash Name: XM_XM25QH64A{0x207017), 0x800000.
@nvt_spinor_validate_params(), XmSpiNor_ProtMgr_probe(): OK.
STDR64FW with page size 256 Bytes, erase size 64 KiB, total 8 MiB
CONFIG_CLOSE_SPI_8PIN_4IO = y.
lk=>10, 0x780000.
SRx val: {[1, 0x28], [0, 0x0], [0, 0x0], [0, 0x0]}, SrVal: 0x100000000000028.
nvt spinor 1-bit mode @ 48000000 Hz, read_opcode: 0x3B, program_opcode: 0x2.
@do_spi_flash_probe() flash->erase_size: 65536, flash->sector_size: 65536
device 0 offset 0x40000, size 0x2e0000
SF: 3014656 bytes @ 0x40000 Read: OK
srcAddr: 0x2000000, dstAddr: 0x3500000, apFileName[0]: boot/uImage.
created_inode 0x3bf8f30
find_squashfs_file: name bin, start_block 0, offset 1654, type 1
find_squashfs_file: name boot, start_block 0, offset 1746, type 1
read inode: name boot, sb 0, of 1746, type 1
find_squashfs_file: name uImage, start_block 0, offset 1686, type 2
read inode: name uImage, sb 0, of 1686, type 2
write_file: regular file, blocks 7
len 1629112
### get_squashfs_file OK: loade 1629112 bytes to 0x3500000
   Image Name:   Linux-4.19.91
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1629048 Bytes = 1.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
 Linux Image is at 3500000, uboot fdt image is at 3bcf108, loader tmp fdt address is at 100000
bootm 3500000 - 3bcf108
## Booting kernel from Legacy Image at 03500000 ...
   Image Name:   Linux-4.19.91
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1629048 Bytes = 1.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 03bcf108
   Booting using the fdt blob at 0x3bcf108
   Loading Kernel Image
   Loading Device Tree to 028f9000, end 028ffd9d ... OK
osMemStart: 0x0, osMem: 0x2900000.
@fdt_fixup_memory_banks(), ddrStart: 0x0, ddrAll: 0x4000000, hdalStart: 0x2900000, hdalSize: 0x1700000, size[0]: 0x2900000.
 
Starting kernel ...
 
ACTLR: 0x00000004
ACTLR: 0x00000044
Disable MMU
Clear MMU
Uboot L2 cache aux val: 0x72420000
Uboot L2 cache prefetch ctrl val: 0x70800000
Uboot L2 cache ctrl val: 0x00000000
Done
Uncompressing Linux... done, booting the kernel.
 
 
</pre>
nt98562.1713291149.txt.gz · Последнее изменение: 08.07.2024 11:48 (внешнее изменение)